Listar Diseño Mecánico, Materiales y Procesos - GIDIMA por título
Mostrando ítems 7-26 de 28
-
Clay surface characteristics using atomic force microscopy
(Revista Facultad de Ingeniería Universidad de AntioquiaColombia, 2018-06-07)The first component for the manufacture of masonry products used in construction is clay, which provides the plasticity that facilitates the molding and handling of the product. The second component is the feldspar in form ... -
Coating of tricalcium phosphates by flame spray
(Journal of Physics: Conference SeriesInglaterra, 2019-11-29)The metal alloys used for prostheses with high mechanical requirements are bioinerts, it means they have low integration with bone tissue, therefore, bioactive coatings are used in order to improve this integration. ... -
A comparative study of the cutting parameter in milling process under different material
(Contemporary Engineering SciencesBulgaria, 2018-06-18)In the present study, the incidence of the variation in feed rate per tooth and depth of cut for SAE 4340 alloy steel and SAE J431 steel castings was analysed and in which material this variation is most noticeable. For ... -
Comparison of the radius of curvature in the cams which used in the displacement law beziér curves and cyclic and harmonic curves
(Contemporary Engineering SciencesBulgaria, 2018-11-07)The work shows the radius of curvature for different variations of the angle of rotation β and of the ratio of Ro/L, the study is shown for the case in which the laws of displacement of the cams have been designed by ... -
Design of an automated cheese cutting machine prototype
(Contemporary Engineering SciencesBulgaria, 2018-11-30)This work describes each of the parameters for the design of a prototype of an automated machine to make cuts in different types of cheese, in cubic form and slices. Each mechanical and structural component is designed, ... -
Determinación experimental de la formabilidad de láminas de acero SG295 mediante sus propiedades tensiles
(Revista Colombiana De Tecnologías De AvanzadaColombia, 2017)En la presente investigación experimental se determinaron los límites de formabilidad de láminas de acero SG295 de 2.2 mm de espesor, las cuales son utilizadas en la manufactura de cilindros para gas. Se realizó inicialmente ... -
Determination of correlation of compressive strength with maturity of concrete mixed with accelerator
(Journal of Physics: Conference SeriesInglaterra, 2019-11-29)The compressive strength of concrete mixtures with accelerator additives designed for structural elements with strength of 5000 psi was correlated with the maturity index of concrete at an early age. The design of the ... -
Determination of the theoretical stress concentration factor in structural flat plates with two holes subjected to bending loads
(Contemporary Engineering SciencesBulgaria, 2018-11-22)Numerous research works have studied the stress distribution in sections with geometric discontinuities and the relationship with the theoretical factor of stress concentration using the finite element method. These works ... -
Effects of Environmental Conditions on Photovoltaic Generation System Performance with Polycrystalline Panels
(International Journal on Advanced Science Engineering and Information Technology, 2021-10-31)Photovoltaic solar energy is the third most widely used renewable source worldwide, after hydroelectric and wind energy, and this energy source requires experimental and theoretical development in specific topics such as ... -
Evaluation of the drinking water treatment system (STAP) San Fernando –Los Patios urbanization, Colombia. Efficiency and quality
(Revista UIS IngenieríasColombia, 2020-08-26)The quality of water for human consumption in the municipality of Los Patios in Colombia, depends 60% of the treatment systems for drinking water (STAP) independent, these are adapted according to the ... -
Experimental study of the 2D variability roughness in the honing process of the steel cylinder
(Contemporary Engineering SciencesBulgaria, 2018-05-29)This article presents the study of the surface roughness inside cylinders, machined by honing in industrial honing machines, with a detailed review of the variability of the values obtained in the measurement of the ... -
Experimental study of the correlation the surface roughness 2D and 3D in the honing process of the steel cylinder
(Indian Journal of Science and TechnologyIndia, 2018-08)Objectives: This research proposes the feasibility of working on surfaces obtained by honing with 2D roughness parameters, as the 3D roughness measurement commonly used in the industry requires many hours of measurement ... -
Gerencia estratégica de proyectos: Aplicación del modelo de Constructibilidad
(RespuestasColombia, 2018-07-28)La presente indagación está dirigida a proponer estrategias gerenciales para la administración de proyectos de construcción, la cual se basa en un conjunto de conocimientos y experiencias que a lo largo del tiempo ha dado ... -
In vitro study of the proliferation and growth of human fetal osteoblasts on Mg and Si co-substituted tricalcium phosphate ceramics
(Journal of Biomedical Materials Research Part AInglaterra, 2017-04-20)The objective of this work was to study the feasibility of the solid state sintering, a conventional ceramic processing method, to obtain Mg and Si co-substituted tricalcium phosphate bioceramics and composites containing ... -
PEST analysis of wind energy in the world: From the worldwide boom to the emergent in Colombia
(Journal of Physics: Conference SeriesEstados Unidos, 2018-12-07)This article presents the analysis of the political, economic, social and technological aspects of the countries with the greatest development and generation of wind energy in the world, with the aim of studying the successes ... -
Principal stresses on the contact surface of a cam-tracker mechanism designed using Bézier curves
(Contemporary Engineering SciencesBulgaria, 2018-11-29)The study exposes the variation of the main stresses in a cam mechanism with roller follower whose profile has been designed by means of Bézier curves. The contact theory for the cam case is proposed and the distribution ... -
Processing and in vitro bioactivity of a β-Ca3(PO4)2-CaMg(SiO3)2 ceramic with the eutectic composition
(Boletín de la Sociedad Española de Cerámica y VidrioEspaña, 2016-02)In this study, a dense bioactive ceramic, with nominal composition (wt.%) 40 Ca3(PO4)2–60 CaMg(SiO3)2, was prepared by solid state sintering of homogeneous compacted mixtures of fine synthetic Ca3(PO4)2 and CaMg(SiO3)2 ... -
Scientometric analysis of research on emissions control from 2007 to 2017
(International Journal of Applied Engineering ResearchColombia, 2018-01)A scientometric analysis of the production of scientific publications on emissions control from 2007 to 2017 was carried out. HistCite was used to analyze information collected from Web of Science (WoS) on this topic during ... -
Síntesis en estado sólido y caracterización de fosfato tricálcico dopado con magnesio y zinc
(Revista Latinoamericana de Metalurgia y MaterialesVenezuela, 2017-04-23)El desarrollo de biocerámicas para aplicaciones estructurales está limitado debido a su baja tenacidad y resistencia. Estas limitaciones conllevan a investigaciones que buscan mejorar su rendimiento mecánico mediante dopado ... -
Study of the fire decomposition behavior of recycled polyethylene terephthalate (RPET) with the addition of MCA additive retardant
(Journal of Physics: Conference SeriesReino Unido, 2018-12-07)Polyethylene terephthalate (PET) currently occupies an important space in the manufacture of bottles for carbonated beverages and mineral water, however, its use has become another pollution problem in the world, due to ...